PDI Front Mount Intercooler Mazda BT-50 3.2L 2011-2022

$1,600.00

PDI Front Mount Intercooler Mazda BT-50 3.2L 2011-2022

PDI Front Mount Intercooler Ford Ranger
This item: PDI Front Mount Intercooler Mazda BT-50 3.2L 2011-2022
$1,600.00
$1,600.00
105 Series 1FZ Turbo PDI Intercooler Kit
1 × 105 Series 1FZ Turbo PDI Intercooler Kit
DRIVELINE OPTION
TURBO SETUP
$1,950.00$2,470.00
  • Worldwide Shipping
Guaranteed Safe Checkout

PDI Front Mount Intercooler Mazda BT-50 3.2L 2011-2022

The latest update to the PDI intercoolers for the Mazda BT-50 makes easier fit with the updated facelift model through to the last of 3.2L (2022) model. The facelift model also saw a change to the radiator support panel, which allows us to fit the core further back without dropping the height (more than 20mm) and therefore allow the addition of the transmission cooler kit – see below if you have a PX1 as we think it should also fit there with some tweaks.

The new core is 680 x 260 x 76 with slighter tighter end tank setup. This new design works with our class leading PDI transmission cooler kits, which need to be a serious consideration for any owners of the auto transmission model.

Fully cast end tanks ensures they are the strongest possible and least likely to split along a seam. We have had the air temperature sensor cast into the end tank as well as a oil drain.

All piping is stainless steel and the turbo side piping is rerouted to be significantly shorter and with a single 63mm pipe.

Core is positioned further back at the bottom to allow the fitment of a winch.

The first of the PDI  Mazda BT-50 Front Mount Intercooler designs core is 700x300x76mm and has bigger and high flow cast alloy end tanks. These are still available.

If you have a PX1 Ranger with auto transmission, we think it should be possible to fit our updated intercooler and transmission cooler.

The centre (vertical) support is part of the radiator support panel and can not be purchased individually and welded into the original panel. The facelift used a new bonnet latch (attached with 2 bolts) and the centre support design sits slightly further back.

After removing the lower bolt we found that the latch was still rock solid so to replicate the design of the PX2 we would cut the lower mount from both the latch and the centre support. The updated intercooler will then be able to sit under the latch and if the intercooler still hits we would consider adding thicker spacers behind the upper intercooler mount or adjusting the centre support in the area just under the latch – call us to discuss.

Additional information

Weight 30 kg
Dimensions 100 × 50 × 25 cm

Brand

PDI Intercoolers

Also known as PDI Coolers or Performance Diesel Intercoolers was started by Brian Wiese to fill a gap in the market for those pursuing the full power capabilities in modern diesel engines. This is from a mild 20% power upgrade to increases of over 200% where it is important to keep EGT down while making power. The interest in turbo diesels began in 2005 after managing to import two top spec 80 series 1HD-T powered Landcruisers from Japan before the 15 year import rule was shut down by the government.  It wasn't long before the boost was wound up and the fuelling changed to improve performance. Over the years the trusty 80 Series had had four different intercooler systems of different design with different results.  One of the kits systems worked great until the turbo was upgraded and then it too was needing to be upgraded. The air-water system needed constant maintenance and my initial plumbing for one of the air to air systems was painful.  The final iteration is still in place after more than 7 years. Skipping forward a few years..........while working in Perth at GTurbo we had a need for intercooler systems that would compliment the high performance Grunter Extreme and Badboy turbochargers.  Our experience told us that front mounted air to air intercooler systems were the way to go, but the available systems on the market were all about catering standard turbo and mild turbo upgrades. We were surprised by the effectiveness (both good and bad) of some top mount units from HPD and Cross Country Interoolers, but when asked for our recommendation it had to be a front mount intercooler on the only way to meet the requirement was a custom installation. Time and time again the results showed us we were doing the right thing so as we got more busy we knew a kit system was the only way we could continue to recommend and provide the best solution for customers.  PDI was born out of this need for a better product and a hope that we could be the ones to make it. I have managed a few interesting 4WD trips around the place including two trips up the Canning Stock Route, once from Cairns to Cape York and a more adventurous drive from near Beijing, China through Mongolia and a 4 week jaunt along the Siberian Road of Bones and down to Vladivostok Siberia.  Each of these trips teaches you something new about durability and preparation.  It is the simple things that catch you out so the design has to be right.  The car we used to get through Mongolia and Siberia was an 80 series petrol from Perth converted to a 1HZ and fitted with a turbo and custom intercooler kit.  The extra power it gave provided some really memorable moments through the zig zag mountain passes or pushing through long muddy (and un-neccessary) stretches at speed that would have otherwise left us stranded. The setup has flawlessly completed two international trips trip including being driven from Malaysia, via Mt Everest and on to Norway. In 2017 it went to Africa, unfortunately without me. In 2018, it toured South America, once again as a support vehicle with many spares on board. The affect of a well designed and aesthetically pleasing installation that allows your performance gains to be achieved is very satisfying. We get many calls from customers who have completed the installation and and impressed with the results achieved. Our aim is provide customers with a kit that will exceed their expectations.  If we don't think an upgraded intercooler is going to make a difference on your vehicle and provide maximum benefit for your money spent we will make other suggestions. Where are we going from here? We have been revamping designs and making the cores larger and more effective than originally expected. Every time we fit one of the new designs we know without a doubt that we have made it the biggest that is possible. Additionally we are expanding the range with the same philosophy and the results speak for themselves. Having a powerful HDJ79 with over 300rwkw as the daily work ute is very nice. We also believe that, even though the power has increased more than 3x factory, it is still reliable and can be driven anywhere and used for many different duties.

Reviews

There are no reviews yet.

Be the first to review “PDI Front Mount Intercooler Mazda BT-50 3.2L 2011-2022”

Your email address will not be published. Required fields are marked *